Easy Flower Headbands

So, a few people have called the warehouse lately asking what exactly you might do with some of the new flowers we’ve gotten in. Namely the shabby flowers and rolled rosettes. There are lots of things to do with them, but today I’m going to show you one of the  most popular (and cute!).

I didn’t feel the need to create a tutorial on these trendy little headbands because they are really just so simple.I just hot glued the flowers straight onto the headbands. Easy peasy, right? And really oh so cute! You can make them to match any outfit!  Just pick out a few of your favorite flowers, get your glue gun and imagination and you are set.  You could add a little pizazz with some rhinestones too if you fancy.

I made these in Valentine and Spring colors for a couple of reasons. One, because spring just feels like it must be right around the corner (since we have had SO MUCH snow!).  Second, because we are GIVING THEM AWAY!  Just leave a comment on this post with your favorite new girl’s fashion trend, and we’ll pick a winner with random.org three days from now!

These flowers would also be wonderful attached to an alligator clip and slipped through our crochet headbands.  Remember, we have wonderful wholesale products and prices to make such cute, fun, headbands, clips, tutus, and anything girly you can dream up!

Hooray for fun free stuff!  Comment now for your chance to win!  We will pick a random winner on Friday, 2/8/13 at noon MST so it goes out before the mail leaves (if you get back to us with your address in time).  Good luck!! Veronica, you are the winner, check your email! :)  Congratulations. (We had so many comments, thank you.  We had to go through and delete all of the old ones.  Thanks everyone!)

Tutorial: Layered Spike Bow

I have to say, this is my favorite bow tutorial so far. I hadn’t really expected it to turn out so well, but I just love it. And now I get to teach all of you how to do it!

Layered Spike Bow

You will need:

Layered Spike Bow SuppliesRibbon pieces–measurement and qty purely depend on how big you want your bow and how many layers you’d like. I ended up with 4 layers. I didn’t use the lime green 5/8″ ribbon pictured.

Scissors

String

A Lighter

Directions:

Start by cutting your ribbon pieces down to the length that you want them. As I said above, the length you need depends totally on how you want your bow to look. My bow ended up at about 4.5″ wide. The Pink layer on bottom was cut at 5″ before trimming and sealing. Then I cut each layer a little bit smaller than the one under it. I didn’t use the lime green ribbon 5/8″ ribbon because I just thought there were enough layers without it.

Then, cut the ends how you like them to look. I like mine in V cuts. So that’s how I cut them except the 3/8″ swiss dot ribbon. I just angle cut that because it was too small.

This is how I V cut. Fold your ribbon in half, then cut from the fold down toward the corners on the end. Perfect V every time.

Now heat seal all of your ends. This takes some time, but don’t skip it unless you want your ribbon to fray. Just run a lighter really quickly over all of the V-cut ends. Don’t linger–you will start to burn the ribbon (speaking from experience :)).

Take the ribbons that will go on bottom and crease fold them in the center like this:

Still holding your first creased ribbon, do the second and third ones the same way–holding all of them tight.

Now, hold them together and wrap the string tightly around the center. Tie a knot in the string and trim loose ends. That’s your first layer!

Do this to all of your other ribbons putting them together as you see fit–no rules here.

Next, take your glue gun and glue the layers together in the center where the string is tied one by one, stacking them on top of one another.

Tie more string around the entire stack to help keep it from falling apart in some poor little girl’s hair.

Now just hot glue a small piece of coordinating 3/8″ ribbon around the center and heat seal the ends. Voila–super sweet layered spikey bow!

Layered Spike Bow**Note**This bow is the 4th piece in a 6 part series that ends in a stacked bow tutorial. The other pieces in the series are:

Step 1: Lined French Clip

Step 2: Boutique Bow

Step 3: Loopy Surrounder Bow,

Step 4: Layered Spikey Bow

Step 5: Topper Bow

Step 6: Putting it all together Stacked Bow.  If you don’t have time, or want to purchase all of the supplies, we do have a lot of hair bows for sale.  We have a huge selection of wholesale, cheap hairbows that you can purchase.

Tutorial: How to Line a French Clip

How to line a French ClipI never knew how to do this, and honestly never thought of doing it. But my niece had a bow with a lined french clip in her hair the other day that just seemed like it looked a lot more ‘finished’ than an exposed one.

So I decided to find out how to do it. And today I pass that knowledge onto you!

You will need:

How to line a french clip suppliesFrench Clip (this one is 8 CM, or 80MM)

3/8″ Grosgrain Ribbon Piece (this one is about 8″ in length)

Scissors

Glue Gun and Sticks (not pictured)

Lighter (not pictured)

Directions:

Start by taking the center bar out of your clip being careful not to bend it like I did :)

Now place a dab of hot glue on the inside of one end on your clip. It doesn’t really matter which end.

Stick one end of your ribbon in on top of the hot glue pretty side up. This actually may be easier if you put the ribbon in first and then put the hot glue under it once you have it in position. Hindsight………….

Turn your clip over and run a bead of glue down the length of your clip.

Wrap your ribbon around the end and over the glue adhering it to the clip.

Wrap the ribbon around to the back again and under the little prongs on your clip.

Run a bead of hot glue down the length of the inside of the clip, pull the ribbon taught and press it down onto the hot glue adhering the ribbon to the clip.

Trim off any excess ribbon  and use your lighter to heat seal the ends. Just run a flame over the exposed end quickly–don’t linger or it will burn your ribbon.

Now just put your center bar back in (carefully), and voila! Wasn’t that easy? And I just think it really makes your hair bows a lot more finished and professional looking.

Thanks for visiting, and make sure to come back often for more fun ideas and tips!

How to line a French Clip

**Note**This is the 1st piece in a 6 part series that ends in a stacked bow tutorial. The other pieces in the series are:

Step 1: Lined French Clip

Step 2: Boutique Bow

Step 3: Loopy Surrounder Bow,

Step 4: Layered Spikey Bow

Step 5: Topper Bow

Step 6: Putting it all together Stacked Bow