Patriotic Sparkler Bow!

Who wants to see how I made this fabulous 4th of July themed boutique bow?  Isn’t this just so festive?  I love patriotic and red/white/blue items, especially on little girls.

Patriotic Hairbow

I actually have some cousins with daughters (lucky ladies!) who are going to be entering a local children’s parade. They are planning on a patriotic theme for their group, so they had asked me if I could teach them how to make some cute patriotic themed bows.

So, this is for them–and of course–for you!

You will Need:

1 Boutique Bow–tutorial at this link

1 Stacker Bow–tutorial at this link

1 8CM Lined French Clip–tutorial at this link

A Few Pieces of Star Wire Garland

A Rhinestone or Center Embellishment (optional)

A Scrap Piece (maybe 6″8″ long) of 3/8″ Grosgrain Ribbon

About 12″ of String

Hot Glue Gun and Glue Stick (not shown)

Directions:

Start by hot gluing your stacker bow to your boutique bow–center to center.

Lay your pieces of wire garland in a straight horizontal line center to your bow. Use the string to tie them to your bow nice and tight.

Now your thinking, “that is not cute” lol. That’s what this next step will take care of.

Pull your wire garland and fan it out on each side of the center string. Trim it up if you’ve made your pieces too long for your liking.

Now hot glue that scrap piece of coordinating 3/8″ grosgrain ribbon to the center of your bow like so. This piece will hide that ugly string you used in the last step.

Now flip your bow over to the backside. Take the center bar out of your lined french clip and hot glue it to the center of the back of your bow.

Wrap your 3/8″ grosgrain ribbon up and hot glue it to the french clip. Then trim the end off and run a lighter over it to heat seal it from unraveling. Do this to both ends of the ribbon.

Put the center bar back into your clip.

This is actually very cute without any center embellishments. So, you could just leave it this way.

4th of July Hairbow

Or, you can be like me, and just have to add a little more bling.

So, I hot glued the rhinestone to the center of my bow.

Voila! Done–isn’t it just adorable?

Red/White/Blue Hairbow

Thanks for stopping by our blog today–leave some love for us if you like it!

And stay tuned for more tutorials and other fun posts!

Tutorial: Layered Spike Bow

I have to say, this is my favorite bow tutorial so far. I hadn’t really expected it to turn out so well, but I just love it. And now I get to teach all of you how to do it!

Layered Spike Bow

You will need:

Layered Spike Bow SuppliesRibbon pieces–measurement and qty purely depend on how big you want your bow and how many layers you’d like. I ended up with 4 layers. I didn’t use the lime green 5/8″ ribbon pictured.

Scissors

String

A Lighter

Directions:

Start by cutting your ribbon pieces down to the length that you want them. As I said above, the length you need depends totally on how you want your bow to look. My bow ended up at about 4.5″ wide. The Pink layer on bottom was cut at 5″ before trimming and sealing. Then I cut each layer a little bit smaller than the one under it. I didn’t use the lime green ribbon 5/8″ ribbon because I just thought there were enough layers without it.

Then, cut the ends how you like them to look. I like mine in V cuts. So that’s how I cut them except the 3/8″ swiss dot ribbon. I just angle cut that because it was too small.

This is how I V cut. Fold your ribbon in half, then cut from the fold down toward the corners on the end. Perfect V every time.

Now heat seal all of your ends. This takes some time, but don’t skip it unless you want your ribbon to fray. Just run a lighter really quickly over all of the V-cut ends. Don’t linger–you will start to burn the ribbon (speaking from experience :)).

Take the ribbons that will go on bottom and crease fold them in the center like this:

Still holding your first creased ribbon, do the second and third ones the same way–holding all of them tight.

Now, hold them together and wrap the string tightly around the center. Tie a knot in the string and trim loose ends. That’s your first layer!

Do this to all of your other ribbons putting them together as you see fit–no rules here.

Next, take your glue gun and glue the layers together in the center where the string is tied one by one, stacking them on top of one another.

Tie more string around the entire stack to help keep it from falling apart in some poor little girl’s hair.

Now just hot glue a small piece of coordinating 3/8″ ribbon around the center and heat seal the ends. Voila–super sweet layered spikey bow!

Layered Spike Bow**Note**This bow is the 4th piece in a 6 part series that ends in a stacked bow tutorial. The other pieces in the series are:

Step 1: Lined French Clip

Step 2: Boutique Bow

Step 3: Loopy Surrounder Bow,

Step 4: Layered Spikey Bow

Step 5: Topper Bow

Step 6: Putting it all together Stacked Bow.  If you don’t have time, or want to purchase all of the supplies, we do have a lot of hair bows for sale.  We have a huge selection of wholesale, cheap hairbows that you can purchase.