How to Make a Pony-O

With summer coming, lots of kids, including girls, will be playing a lot of different sports. So, I thought it would be fun to show you how to make these pony-o holders for ponytails since we like to have our hair up during sports, right?  They are also great for cheer and cheer leading.

Plus, this is a really great project for using up a bunch of old scraps. Or, you can make a bunch for your daughter’s whole team if you buy ribbon!

Excuse the messy hair–I only had myself for a model today :)

Cheer Pony-OYou will need:

Cheer Pony-O SuppliesScrap Ribbon pieces

Elastic Pony Holder

Scissors

Needle and Thread

Glue Gun and Stick (not shown)

Directions:

Start by cutting your ribbons all about the same length however long you’d like them to hang. If you want them to vary in length, you can trim them up after you are done.

Now, stack your ribbons however you want them to look. I put my wider black ribbon on the bottom then stacked them up according to width. But you can do it however you like.

Gather your ribbons in about the center–you don’t have to be perfect. Just approximate.

Take your needle and thread and sew a basic basting stitch down the center of your ribbons making sure to catch them all in there at least once. This will just make sure that when your little girl is wearing this, the ribbons won’t slide out or become uneven.

Once you have pulled your thread through, you can take the needle off. Or you can use it to aid in tying. I tend to poke myself, so I take it off :)  Leave some tails on each side of your ribbons with the thread to use for wrapping.

Now fold your ribbons down the center accordion style, like so:

Wrap the thread around the folds until you feel it is fairly secure.Don’t tie off yet though.

Now hot glue your ponytail holder to the backside on the center of your ribbon bunch being careful not to get hot glue on your ribbons like I did :(

Wrap the thread tails around the ponytail holder and ribbons just to help secure it a little bit more. When you’re comfortable that it is good and secure, tie the tails together in a knot or two and snip the leftover ends off.

Take a scrap piece of ribbon (for wrapping around the center of your pony-o, and tie a knot in the center. I tied two because my ribbon was small.

Hot glue the knot to where you want the front top of your pony-o to be. Then trim the ends however short they need to be to wrap around the pony-o and elastic ponytail holder. Hot glue the ends around the center of your pony-o holder.All that’s left to do now is trim up your ends however you want them. You’ll want to heat seal those lightly with a lighter or other heat source to keep them from fraying as well.

Some people add rhinestones or other fun little things by hot-gluing them to your ribbons too. Make it yours!

Tutorial: How to Make a Boutique Bow

Today’s tutorial is on how to make a boutique bow. I used to be pretty intimidated by these bows. I thought they looked hard, but they are actually pretty darn easy, so I’m excited to share that with you today!

Boutique Bow

You will need:

Boutique Bow SuppliesAbout a 30″ Length of 1.5″ Grosgrain Ribbon

A Small Scrap of 3/8″ Grosgrain Ribbon

 Lined Alligator Clips

Some String

Scissors

A Lighter

Glue Gun and Glue Stick (not pictured)

Directions:

Start by laying your ribbon out horizontally flat in front of you. Then take one end of the ribbon and make a loop by pulling the end up and around the flat ribbon.

Now take the other end of ribbon and make a second loop on the other side like this:

Next, bring up that longer piece on the right in the above picture and make another loop that curls under. This part is a bit tricky–you need to tuck the tail of this loop under the tail on the first loop. I hope that makes sense because I couldn’t really get a good photo to illustrate. I did try though.

Below is a picture of the backside of the bow at this point.

Now bring the tail back up and make your last loop curving the tail up through the center of the bow.

Next smoosh the center of your bow together sort of like an accordian.

Wrap the string tightly around the center to keep your bow from unraveling. Once you are comfortable that the bow is secure, tie a knot in the string and trim any loose ends off.

Trim up the tails on your bow. I like to cut mine into V shapes.

At this point you should heat seal the ends of the tails on your bow. Just run a lighter lightly over the V shape cuts you made to prevent the ribbon from unraveling. It doesn’t take much heat–you will see it happen. Be careful not to burn yourself!

Now glue your lined clip to the back of your bow.

Almost done. Next, glue your scrap piece of 3/8″ ribbon around the front of your bow and over the back side of your alligator clip. Trim up the ends and heat seal the 3/8″ ribbon end. Done! Super cute and easy to make bow!

Boutique Bow Tutorial

**Note**This bow is the 2nd piece in a 6 part series that ends in a stacked bow tutorial. The other pieces in the series are:

Step 1: Lined French Clip

Step 2: Boutique Bow

Step 3: Loopy Surrounder Bow,

Step 4: Layered Spikey Bow

Step 5: Topper Bow

Step 6: Putting it all together Stacked Bow

Thank you for taking a look at our hairbow tutorial, directions and patterns.  They are free for you to use.  Our online tutorials are to help you make cheer bows for cheerleaders and cheerleading.  They are also great for little girls.  Making bows is fun and the possibilities are endless.  Come look at our shop to purchase grosgrain ribbon for your hairbows, or to look at our hair bows that are for sale.